Description
Ziegler Uptime Guarantee. Cat Certified Used w/CVA includes Powertrain + Hyd + Tech warranty through 11/21/29 or 5,000 hours with CVA
140 GC 01A MG AM-N DCA2
140GC 01A AWD MOTOR GRADER
CAB, ROPS, HIGH PROFILE, PLUS
CIRCLE SAVER
DECALS, ANSI, AWD
ENGINE, STAGE V, W/O AIR COMPR
LANE 1 ORDER
LIGHTS, WORKING, PLUS
MOLDBOARD, 14', PLUS
Online Owner's Manual
PREMIUM CORP RADIO (12V)
ROLL ON-ROLL OFF
SEAT, CLOTH, AIR SUSPENSION
SERIALIZED TECHNICAL MEDIA KIT
STORAGE PROTECTION
Steering: SECONDARY
Precleaner: NON SY-KLONE
Global Arrangement
Fan: STANDARD AWD
Mirror: EXTERNAL BASIC
Film: CHINA EMISSION
Mount: SWITCH GROUP
Covers: UNDER CAB OR CANOPY
Warning Beacon: CE
Tool Box
Link Bar: HYDRAULIC AWD
No Lock Out: CAB
Mirror Group: INTERNAL
No Accumulators
Base + 2 (rip: FL)
Equipment-certification-code: CCU
Hvac: W/O AIR COMPRESSOR AWD
Remaining Factory Warranty
Customer Value Agreement (cva)
AuxiliaryLighting: FRONT AND REAR FACING, HIGH BAR
Camera
Drawbar: SLIP CLUTCH
WalkboardExtensions
ColdWeatherPackage: COLDSpecifications
Year2023
ManufacturerCATERPILLAR
Model140GC
Hours397
Serial NumberW9500342
ConditionUsed
Stock NumberEQ0095611
TelematicsYes
Tire Width17.53 in
Year2023|
ManufacturerCATERPILLAR|
Model140GC|
Hours397|
Serial NumberW9500342|
ConditionUsed|
Stock NumberEQ0095611|
TelematicsYes|
Tire Width17.53 in|
Inspection Information
SERIAL NUMBERS
ATTACHMENTSInfo Needed
ENGINE FRONT S/NInfo Needed
ENGINE REARN/A
TRANSMISSION S/NInfo Needed
INTERIOR CAB
AIR CONDITION SYSTEMOkay/Done
AUTO SHIFTOkay/Done
BRAKE OPERATIONALYes (Passed)
CAB FILTEROkay/Done
CLEAN CABYes
CLEAN WINDOWS & INSPECTOkay/Done
CONTROLSOkay/Done
EMS/CMS/GAUGESOkay/Done
FUEL LEVELFull
HEATING SYSTEMOkay/Done
OPERATIONAL MANUALYes (Passed)
PARKING BRAKE OPERATIONAL/ ADJUSTEDOkay/Done
PRODUCT LINK BOXYes (Passed)
RIDE CONTROLOkay/Done
SEAT ADJUSTMENTYes (Passed)
SEAT CUSHIONYes (Passed)
TRANS CONTROLOkay/Done
WASHER FLUID & WIPER CONDITIONOkay/Done
MACHINE
ACCUM CHARGEYes (Passed)
AIR FILTERYes (Passed)
ALL DOOR LATCHESYes (Passed)
BATTERIESYes (Passed)
BELLY PANSOkay/Done
BLOCK HEATERYes (Passed)
BOOMN/A
BRAKE FLUIDN/A
CARRIAGEN/A
CLEAN MACHINEYes
COOLANT LEVELWithin Operating Range
DAMAGE LISTEDOkay/Done
DEF LEVELFull
DRAIN AIR TANKSN/A
EDGES/TEETHOkay/Done
ENGINE OILWithin Operating Range
FAN BELTYes (Passed)
FINAL DRIVEN/A
FRONT AXELN/A
GREASE MACHINEYes (Passed)
HAMMER EQUIPPED MACHINESN/A
HYD CHARGEYes (Passed)
HYDRAULIC OILCorrect
HYDRAULIC PRESSUREYes (Passed)
IS THERE ANY HYDRAULIC/CYLINDER LEAKS? IF SO, WHERE IS THE LEAK?No
KICKOUTSOkay/Done
LAST PM SERVICEYes
LIST ANY PSP/PIPS NEEDED ON MACHINEYes
PIVOT SHAFTOkay/Done
REAR AXELN/A
SWING DRIVEN/A
TIRES (LIST ANY DAMAGE, SIZE, & BRAND)Good
TRACK ADJUSTMENTN/A
TRACK ROLLER FRAMEN/A
TRANSMISSION OILWithin Operating Range
SAFETY FEATURES
BACK UP ALARMOkay/Done
BRAKE LIGHTSOkay/Done
GRAB HANDLESOkay/Done
HEAD LIGHTSOkay/Done
HORNOkay/Done
SAFETY LINKOkay/Done
SEAT BELT (MUST BE REPLACED EVERY 3 YEARS)Okay/Done
SMV SIGNOkay/Done
STROBE LIGHTSOkay/Done
TURN LIGHTSOkay/Done
ZIEGLER/ZIEGLER RENTAL DECALS AND ID#Okay/Done
GRADE CONTROL TECHNOLOGY
3D TECHNOLOGY GRADE CONTROL EQUIPPED: AFTERMARKET OR CAT GRADE. PROCEED TO NEXT STEPS IF EQUIPMENT IS PRESENT. (SECONDARY DISPLAY IN THE MACHINE)N/A
FOR EXCAVATORS: IS THE MACHINE ACCURATE IN 2D AGAINST A LP51G OR LP52G LASER?Yes
PHYSICAL APPEARANCE
ALL CABLING CONNECTED?Yes
ALL HARDWARE INTACT?Yes
WIRING DAMAGED? FRAYS?No
WEB INTERFACE: ADMIN/SITECH#1
ARE 40 RADIO CHANNELS ENTERED? ONLY ON TD5XO TOUCH DISPLAY.N/A
ARE ALL OF THE COMPONENTS FIRMWARE UP TO DATE?N/A
ARE THE UNITS TURNED TO FT AND MPH?N/A
ARE THE VRS CREDENTIALS ENTERED? TO TEST YOU MUST BE OUTSIDE.N/A
DOES THE MODEM HAVE INTERNET?N/A
HAS THE BLADE ROTATION BEEN CALIBRATED WITHIN THE LAST YEAR?N/A
HAS THE BODY SENSOR BEEN CALIBRATED IN THE LAST YEAR? IF NO, RECALIBRATE.N/A
HAS THE PASS MATCH ADJUSTMENT BEEN CALIBRATED IN THE LAST YEAR?N/A
HAS THE VALVE CALIBRATION BEEN CALIBRATED IN THE LAST YEAR?N/A
IS THE SYSTEM ECM FIRMWARE AT 2.16 OR HIGHER?N/A
IS THERE A MACHINE FILE SAVED? ONLY ON TD5XO TOUCH DISPLAY.N/A
IS "SOFTWARE MAINTENANCE UNTIL" DATE OLDER THAN TODAY'S DATE? (IF NO, CONTACT CON TECHNOLOGY SUPPORT)N/A
MONITOR/ONBOARD DEVICES: ALL GREEN?N/A
STORAGE: ARE THE PROJECTS DELETED?N/A
WAS THE SENSOR CORRECTION CHECK PERFORMED ON EARTHWORKS MACHINE? (MUST BE PERFORMED EVERY 1,000 HOURS)N/A
MACHINE CHECK-IN OUTSIDE SHOP (PERMANENT SITE AT BRANCH REQUIRED VRS OR NETWORK ID)
CHECK BLADE TIPS/CUTTING EDGE ON CONTROL POINT (USE ROVER IF AVAILABLE)NEEDS TO BE WITHIN ONE TENTH OF A FOOT) IS IT ACCURATE?N/A
CHECK BLADE TIPS/CUTTING LENGTHS ARE CORRECTN/A
RUN AUTOMATICS BY BENCHING BLADE/BUCKET ABOVE GROUND ON HIGH THROTTLE. MOVE JOYSTICKS WHILE OPERATING TO ENSURE AUTOMATIC CORRECTION. CREATE A POSITIVE 0.5FT OFFSETN/A
SERIAL NUMBERS
ATTACHMENTSInfo Needed|
ENGINE FRONT S/NInfo Needed|
ENGINE REARN/A|
TRANSMISSION S/NInfo Needed|
INTERIOR CAB
AIR CONDITION SYSTEMOkay/Done|
AUTO SHIFTOkay/Done|
BRAKE OPERATIONALYes (Passed)|
CAB FILTEROkay/Done|
CLEAN CABYes|
CLEAN WINDOWS & INSPECTOkay/Done|
CONTROLSOkay/Done|
EMS/CMS/GAUGESOkay/Done|
FUEL LEVELFull|
HEATING SYSTEMOkay/Done|
OPERATIONAL MANUALYes (Passed)|
PARKING BRAKE OPERATIONAL/ ADJUSTEDOkay/Done|
PRODUCT LINK BOXYes (Passed)|
RIDE CONTROLOkay/Done|
SEAT ADJUSTMENTYes (Passed)|
SEAT CUSHIONYes (Passed)|
TRANS CONTROLOkay/Done|
WASHER FLUID & WIPER CONDITIONOkay/Done|
MACHINE
ACCUM CHARGEYes (Passed)|
AIR FILTERYes (Passed)|
ALL DOOR LATCHESYes (Passed)|
BATTERIESYes (Passed)|
BELLY PANSOkay/Done|
BLOCK HEATERYes (Passed)|
BOOMN/A|
BRAKE FLUIDN/A|
CARRIAGEN/A|
CLEAN MACHINEYes|
COOLANT LEVELWithin Operating Range|
DAMAGE LISTEDOkay/Done|
DEF LEVELFull|
DRAIN AIR TANKSN/A|
EDGES/TEETHOkay/Done|
ENGINE OILWithin Operating Range|
FAN BELTYes (Passed)|
FINAL DRIVEN/A|
FRONT AXELN/A|
GREASE MACHINEYes (Passed)|
HAMMER EQUIPPED MACHINESN/A|
HYD CHARGEYes (Passed)|
HYDRAULIC OILCorrect|
HYDRAULIC PRESSUREYes (Passed)|
IS THERE ANY HYDRAULIC/CYLINDER LEAKS? IF SO, WHERE IS THE LEAK?No|
KICKOUTSOkay/Done|
LAST PM SERVICEYes|
LIST ANY PSP/PIPS NEEDED ON MACHINEYes|
PIVOT SHAFTOkay/Done|
REAR AXELN/A|
SWING DRIVEN/A|
TIRES (LIST ANY DAMAGE, SIZE, & BRAND)Good|
TRACK ADJUSTMENTN/A|
TRACK ROLLER FRAMEN/A|
TRANSMISSION OILWithin Operating Range|
SAFETY FEATURES
BACK UP ALARMOkay/Done|
BRAKE LIGHTSOkay/Done|
GRAB HANDLESOkay/Done|
HEAD LIGHTSOkay/Done|
HORNOkay/Done|
SAFETY LINKOkay/Done|
SEAT BELT (MUST BE REPLACED EVERY 3 YEARS)Okay/Done|
SMV SIGNOkay/Done|
STROBE LIGHTSOkay/Done|
TURN LIGHTSOkay/Done|
ZIEGLER/ZIEGLER RENTAL DECALS AND ID#Okay/Done|
GRADE CONTROL TECHNOLOGY
3D TECHNOLOGY GRADE CONTROL EQUIPPED: AFTERMARKET OR CAT GRADE. PROCEED TO NEXT STEPS IF EQUIPMENT IS PRESENT. (SECONDARY DISPLAY IN THE MACHINE)N/A|
FOR EXCAVATORS: IS THE MACHINE ACCURATE IN 2D AGAINST A LP51G OR LP52G LASER?Yes|
PHYSICAL APPEARANCE
ALL CABLING CONNECTED?Yes|
ALL HARDWARE INTACT?Yes|
WIRING DAMAGED? FRAYS?No|
WEB INTERFACE: ADMIN/SITECH#1
ARE 40 RADIO CHANNELS ENTERED? ONLY ON TD5XO TOUCH DISPLAY.N/A|
ARE ALL OF THE COMPONENTS FIRMWARE UP TO DATE?N/A|
ARE THE UNITS TURNED TO FT AND MPH?N/A|
ARE THE VRS CREDENTIALS ENTERED? TO TEST YOU MUST BE OUTSIDE.N/A|
DOES THE MODEM HAVE INTERNET?N/A|
HAS THE BLADE ROTATION BEEN CALIBRATED WITHIN THE LAST YEAR?N/A|
HAS THE BODY SENSOR BEEN CALIBRATED IN THE LAST YEAR? IF NO, RECALIBRATE.N/A|
HAS THE PASS MATCH ADJUSTMENT BEEN CALIBRATED IN THE LAST YEAR?N/A|
HAS THE VALVE CALIBRATION BEEN CALIBRATED IN THE LAST YEAR?N/A|
IS THE SYSTEM ECM FIRMWARE AT 2.16 OR HIGHER?N/A|
IS THERE A MACHINE FILE SAVED? ONLY ON TD5XO TOUCH DISPLAY.N/A|
IS "SOFTWARE MAINTENANCE UNTIL" DATE OLDER THAN TODAY'S DATE? (IF NO, CONTACT CON TECHNOLOGY SUPPORT)N/A|
MONITOR/ONBOARD DEVICES: ALL GREEN?N/A|
STORAGE: ARE THE PROJECTS DELETED?N/A|
WAS THE SENSOR CORRECTION CHECK PERFORMED ON EARTHWORKS MACHINE? (MUST BE PERFORMED EVERY 1,000 HOURS)N/A|
MACHINE CHECK-IN OUTSIDE SHOP (PERMANENT SITE AT BRANCH REQUIRED VRS OR NETWORK ID)
CHECK BLADE TIPS/CUTTING EDGE ON CONTROL POINT (USE ROVER IF AVAILABLE)NEEDS TO BE WITHIN ONE TENTH OF A FOOT) IS IT ACCURATE?N/A|
CHECK BLADE TIPS/CUTTING LENGTHS ARE CORRECTN/A|
RUN AUTOMATICS BY BENCHING BLADE/BUCKET ABOVE GROUND ON HIGH THROTTLE. MOVE JOYSTICKS WHILE OPERATING TO ENSURE AUTOMATIC CORRECTION. CREATE A POSITIVE 0.5FT OFFSETN/A|
